I have to say, reading your blog and watching your videos makes me want to get started immediately on traditional woodworking. The problem I have is that hand tools are hard to come by at swap meets or antique stores out here in Bakersfield, CA. I have made several trips and so far all I have found is a beat-up old Jack plane. I would rather buy used, but I am a little leery of EBay, so my options are limited. Thank you for your posts on what to buy and links to websites. I haven’t bought anything yet, but… Read more »
If I were to give someone new one piece of advice, it would be to buy their chisels new, not used. I have wasted more time and more money trying to save butchered chisels than I want to admit. There’s a good chance that the used chisel will be bellied in the back or pitted at the edge and it will take more than beginner skills to fix it. You may make things worse rather than better. Sure, learn to do this _some_ day, but maybe not as a beginner first thing. I’ve had similar problems with used planes, but it isn’t nearly as bad a problem for a joinery plane. If there are pits that lead to scratches, it may not matter for anything other than a final smoother. Also, a tiny back bevel may save the day on a plane, but you likely don’t want that on a chisel. So, I’m less fussed about planes and, if it all goes south, you can buy a new blade for smoothing work and use the old for rough work (all in the same plane). You can’t buy a new blade for a chisel. Well, you can, but it’s called buying a new chisel. I use 3/8″ a lot. 1/4, 3/8 to handle all the mortises and dovetails and either 3/4 or 1″ for paring shoulders and for fat parts of some dovetails. I probably learn towards the 1″ because there are times you want to reference off the blade to keep moving in a line, like for a housing. I think Lee Valley’s version of the Narex are excellent and mine came with flat backs that could go straight to polishing.
I consider this my “basic” tool list. Although I do not have a dedicated box for these tools, I assure you that they have a great home in cabinets, on shelves, and laying around on benches. When I do need to take my hand tools somewhere, the larger tools end up in a simple tongue and grooved latch box my grandfather owned. The smaller tools are always in my overall pockets. Overalls work great. They have multiple pockets, they’re comfortable, and they protect your upper body and legs. You only have to deal with small chunks of wood getting into the pockets, which can be dealt with if you or your other half are crafty enough to sew some flaps. It doesn’t bother me though. Thanks for your time.
24″ for the chopping block. all of my lumber comes from last years spring clean up. currently have Cherry, White oak, Ash, Hard & Soft Maple as Well as Sasafrass on hand there is also Birch in the woods but none of them have needed to come down yet. I keep two single bevel axes one light one Heavy(2-1/2 lb) which I use depends on how my Elbow feels. A Froe is also required. I think going from tree to board is harder than from board to furniture but it depends how much wind is in the tree. I don’t think I would of ever been able to build the required skills if I had to pay for the lumber though I guess I paid in labor. Air dried stuff is some much better to work with its worth it.
Here’s a list of the 5 basic woodworking tools I’d recommend for beginners to DIY and woodworking. These tools should enable you to build almost anything, and will still be useful even if you upgrade to larger stationary tools later on. These tools would also make great gifts for any of the woodworkers in your life. Enjoy, and let me know what your 5 picks would be in the comments below!
Love this article and the videos, very informative. As a beginning woodworker I have chosen on the traditional means because I can find some good deals at local flea markets and with a little tune up the tools work good. This video give great tips for the new woodworker and the basic essentials needed for getting started. One area I need help is in clamping so I would be honored to win a set of the clamps. If I am not picked for the clamps, an XL shirt would fit (disston seal), my choice of video would be “Building the… Read more »
But before you purchase clamps, build your first project and put it together without glue. Then see how many clamps you think you will need to put enough pressure in all the right spots. Then proceed to purchase that number of clamps. Repeat this process on your next project, and purchase more clamps if needed. This is better than running out and buying a huge collection of woodworking clamps. See my buying guide for different clamp types, uses, and my favorite brands.