If you can buy a bunch of tools at one time, you can save a ton on shipping, as the more you buy, the lower the rates. Also, take advantage of free shipping offers. Compare to see where you can get the best deal. Whatever you buy, make sure it is high quality. I have a Nicholson backsaw I bought at a local store before I knew of the woodworking suppliers. It has never been used much, but cuts much slower than saws such as Gramercy or Lie-Nielsen, even though mine have smaller teeth than the Nicholson.
Love this article and the videos, very informative. As a beginning woodworker I have chosen on the traditional means because I can find some good deals at local flea markets and with a little tune up the tools work good. This video give great tips for the new woodworker and the basic essentials needed for getting started. One area I need help is in clamping so I would be honored to win a set of the clamps. If I am not picked for the clamps, an XL shirt would fit (disston seal), my choice of video would be “Building the… Read more »
If you’re on a tight budget, you can get by with just a dovetail saw for awhile. But if you have the means, then I’d recommend that you purchase three backsaws:  (1) a dovetail saw, with fine rip teeth, used for cutting joinery along the grain (like dovetails), (2) a “carcass saw” used for cutting across the grain (fine cross cut teeth), and (3) a larger tenon saw used for cutting deeper cuts, like tenon cheeks, along the grain (rip teeth). All three saws are used very, very often in my workshop. As mentioned above, you could certainly get by with just a dovetail saw at first, since the small rip teeth don’t do too bad of a job at cutting across the grain. Buying backsaws can be very confusing because most sellers don’t know what saw they have, and the tooth configuration can  change the job of the saw. Most people that sell antique saws mix the names up, so don’t worry. My buyer’s guide really clears this confusion up and will help you know what to look for.

Rabbets are one of the most common joints in furniture making, so a handplane that cuts a rabbet should be toward the top of your list of tools to buy. Yes, rabbets can be cut without a handplane, but at greater difficulty. I own a lot of handplanes that cut rabbets, including wooden rabbet planes, metal rabbet planes, shoulder planes, and moving fillister planes. While I use all of them for specialty tasks, I find that a metal or wooden moving fillister plane (pictured above) is the most useful, as it allows me to cut rabbets with the grain, across the grain, and allows me to easily cut panels (as seen above). And the movable fence helps greatly with accuracy. I discuss rabbet planes in great detail in the handplane buyer’s guide.
I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.
This heavy-duty Combination Machine joints and planes using This heavy-duty Combination Machine joints and planes using the same 12 in. cutterhead saving money and the space required for 2 individual machines. Conversion from the jointer to the planer is easy. Just remove the quick-release fence and flip up the jointer tables. The tables are precision-ground to a mirror-like ...  More + Product Details Close
I created the above hand tool buyer’s guides to help beginners who feel overwhelmed when trying to understand which hand tools they need first. It’s frustrating! Below you’ll see my summary list of the 20 basic professional woodworking hand tools that you should start to accumulate in order to start building the most basic woodworking projects. When you’re ready, you can follow the yellow buttons to visit each of the buying guides for each type of hand tool, to get help with understanding hand tool features, brands, & models. At the bottom of this page is a handy full list of tools that is sorted by “urgent”, “semi-urgent”, and “not-urgent” to buy.
When I came across your blog I was preparing to get started and looking for pointers, and decided to buy your series. In my opinion the choice to show the options was a good one. The series presented a clear overview of hand tool woodworking and you made it look easy and impressive at the same time. That series gave me the confidence to pick up the plane and start woodworking instead of coming up with a long savings plans to outfit a machine-shop. Thus, it was more an inspirational series than a build-along for me. I decided that was the kind of woodworking I wanted to be doing and began practicing. When you minimalised your kit for the later series, the builds themselves became more accessible. I felt I could actually build the pieces with the tools I had available. As a whole, you have provided me with the confidence to get started and the basic skills to continue.
I was telling my brother of the different ways I sharpen and he seemed interested in the slab/sandpaper method. When I went to get the extra supplies I picked up a slab of granite, adhesive, and sandpaper for sharpening. When the job was completed, the saw, the can of finish, and the slab with sandpaper were gifted to my brother. I could have shortened my list a little,
The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using a random sanding motion instead. This motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.
A good set of 5-7 bench chisels (they don’t have to match) will get you going right away. Down the road you’ll eventually add some specialty chisels (like paring chisels, fishtail chisels, etc) but bench chisels will work for just about everything. I often pay only $10 for high quality vintage chisels, so a compiled set can certainly be affordable, and higher quality than low quality new sets. Read the chisel buying guide to learn what chisels to avoid and which chisels will work great.
I have to say, reading your blog and watching your videos makes me want to get started immediately on traditional woodworking. The problem I have is that hand tools are hard to come by at swap meets or antique stores out here in Bakersfield, CA. I have made several trips and so far all I have found is a beat-up old Jack plane. I would rather buy used, but I am a little leery of EBay, so my options are limited. Thank you for your posts on what to buy and links to websites. I haven’t bought anything yet, but… Read more »

Own one junk chisel, probably about 1″. This will keep you from doing what you oughtn’t to your good chisels. It can be used and can be nearly trash. It’s going to hit caulk on masonry, junk stuck to the floor, interior cuts on thin sheets of aluminum, and other such abuse. If the back and bevel sort of intersect on an extra coarse stone, it’s sharp. I’ve sharpened mine on the concrete back stoop. (Not so great for the concrete)
Basic woodworking tools are different from beginner woodworking tools. For one thing, I don’t like to use the word “beginner” unless I am using it accurately. It’s not a very useful label, in my opinion, because it implies that there are clear-cut and hierarchical steps in your growth as a woodworker. Who wants to return to grade school during his or her valuable shop time? So I only use the word “beginner” when I’m talking about someone who is touching woodworking tools for the first time.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
11-2. Pipe clamps, I have about 10 of them with varying lengths of black pipe in 1′ increments. I can switch out the clamps for larger lengths on larger projects, or downsize as needed. (very rarely do I need more than 6 clamps on a project during drying time, and when I do, it’s time for a cup of coffee and a 1/2 hour break while I wait) You keep your initial investment down, and buy them as you need them to increase your collection.

More than a decade ago I spent 2 weeks in Maine aspiring to learn furniture making. On my return home I started enthusiastically planning to turn my basement into a proper shop – with all the “essential” tools I had learned to use. My list reflected my engineer’s preference for buying quality and quickly exceeded $25k in power tools alone (table saw, band saw, joiner, thickness planer, drill press…) even before solving the power, lighting and dust challenges.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
Dan, I’m worried about you. The stress must be getting to you. Somehow you’ve lost your ability to count. By my estimation, your list has at least 29 items, some of which are actually “sets” of items, like chisels or crayons, which I only counted as one item. Perhaps you need a break from all that blogging, and time to get back to basics, like counting. I can help. Come over to my shop and we can count things like parts, items on the honey-do list, and for extra credit, screw holes. Don’t worry about making mistakes, I’ll guide you through it, and we can round up if necessary. Ha!
The block height’s going to be a personal thing, depending on what you use it for. Mine’s about knee height, which is on the low end, but I did use to do a tremendous amount of prepping straight from the tree. As you’re the same height as me, I’d say 33″ would be a tad on the high side. If you imagine you’ve got a longish piece of wood to work down the length, you want to be holding it almost vertical, rather than angled as it’s less likely to slip. The higher the working surface, the more angled it’s naturally going to become, hence why mine’s so low.

If you’re on a tight budget, you can get by with just a dovetail saw for awhile. But if you have the means, then I’d recommend that you purchase three backsaws:  (1) a dovetail saw, with fine rip teeth, used for cutting joinery along the grain (like dovetails), (2) a “carcass saw” used for cutting across the grain (fine cross cut teeth), and (3) a larger tenon saw used for cutting deeper cuts, like tenon cheeks, along the grain (rip teeth). All three saws are used very, very often in my workshop. As mentioned above, you could certainly get by with just a dovetail saw at first, since the small rip teeth don’t do too bad of a job at cutting across the grain. Buying backsaws can be very confusing because most sellers don’t know what saw they have, and the tooth configuration can  change the job of the saw. Most people that sell antique saws mix the names up, so don’t worry. My buyer’s guide really clears this confusion up and will help you know what to look for.

About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.
Here’s a list of the 5 basic woodworking tools I’d recommend for beginners to DIY and woodworking. These tools should enable you to build almost anything, and will still be useful even if you upgrade to larger stationary tools later on. These tools would also make great gifts for any of the woodworkers in your life. Enjoy, and let me know what your 5 picks would be in the comments below!

Always be on the lookout for usable wood. You might be able to salvage some. You can use a metal detector to find nails and screws. You don’t need a full fledged metal detector. I use a pinpointer made by Garrett. If your wood has some woodboring beetles you can still use it if not eaten too badly. A healthy dose of cyfluthrin will take care of them.
No matter what woodworking or tool-related venture you're taking on, Amazon.com has the trustworthy brands delivering the helpful products you'll want, brands like Dewalt, Makita, Stanley, Black + Decker, Festool, Shop-Vac, Jet and more. You'll also find a wide range of deals and special offers on woodworking products in the Deals and Savings page. Shop on Amazon.com and get free shipping for qualifying orders.

On chisels, once a new comer learns to sharpen, Aldi sells a 4 chisel pack for about $20 US. They are blunt and the backs need to be flattened but once correctly sharpened, they hold their edge very well. These are my go to chisels for most work and they’re as sharp as a scalpel. My good chisels haven’t seen the light of day in over a year as the Aldi chisels work beautifully.


The very affordable coping saw (usually under $20) is regularly used for rough cutting shapes in the board, but especially for removing waste from dovetail joints (one of the most common wood joints). An affordable coping saw will work just fine, along with a pack of affordable replacement blades. Read my hand saw buying guide for more detail on brands & features to look for when purchasing a coping saw.
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.

A good set of 5-7 bench chisels (they don’t have to match) will get you going right away. Down the road you’ll eventually add some specialty chisels (like paring chisels, fishtail chisels, etc) but bench chisels will work for just about everything. I often pay only $10 for high quality vintage chisels, so a compiled set can certainly be affordable, and higher quality than low quality new sets. Read the chisel buying guide to learn what chisels to avoid and which chisels will work great.
A good set of 5-7 bench chisels (they don’t have to match) will get you going right away. Down the road you’ll eventually add some specialty chisels (like paring chisels, fishtail chisels, etc) but bench chisels will work for just about everything. I often pay only $10 for high quality vintage chisels, so a compiled set can certainly be affordable, and higher quality than low quality new sets. Read the chisel buying guide to learn what chisels to avoid and which chisels will work great.

As someone who is just progressing past being a “beginner” (just getting into building furniture) in the woodworking community, I would say there are a number of changes I would make to your list. First, I would say that a power jointer/thicknesser does not belong on the list by any means. They are way too large of an investment and take up a lot of space (not to mention you can buy your stock at the desired dimensions). I also strongly disagree with the concept of joinery devices. As someone new to the trade, I feel this is a very important skill that must be developed, not skipped over by buying devices power devices that achieve a single goal. I think the jigsaw should be replaced by a good bandsaw. I just purchased my first major power tool and it was a 14″ bandsaw and not a tablesaw for space reasons as well as versatility. The bandsaw allows me to resaw, cut curves, (now that it is adjusted for drift) rip pieces of stock accurately that are thicker than a table saw could handle, etc. Once the cut is complete, a handplane can remove any saw marks and square/flatten a surface. It is also really useful for cutting tenons and dovetails. Handsaws can be used for crosscutting and anything else the bandsaw cannot handle. As for a bench, if you are getting into woodworking, this should be your first real project (and it is not expensive to make). You are also missing a good vise to be attached to the bench.
As someone who finds hand planing a challenge the minimalist approach seems like the best way to truly learn a tools quirks and develop the skill required. So the Veritas BU planes are going along with the Tormek required to sharpen those gargantuan irons and a diamond plate and oil stone are on the way to get my old Stanley no 5 humming. I never found a sharpening routine that didn’t look a ball ache to keep the BU planes working well and being a stick thin wimp the weight of the buggers for anything more than controlled smoothing shavings knackered me out.

Dan, I’m worried about you. The stress must be getting to you. Somehow you’ve lost your ability to count. By my estimation, your list has at least 29 items, some of which are actually “sets” of items, like chisels or crayons, which I only counted as one item. Perhaps you need a break from all that blogging, and time to get back to basics, like counting. I can help. Come over to my shop and we can count things like parts, items on the honey-do list, and for extra credit, screw holes. Don’t worry about making mistakes, I’ll guide you through it, and we can round up if necessary. Ha!
×