Many beginners trying to get started in woodworking take one look at their budget and worry about how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects.
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.
My Stanley 51/2 was in a bit of a state when I got it and refurbing it took a bit of time and cash. Now it works a treat and looks like new. I’m nearly through the bench build and have spend hours using it – it really is a workhorse piece of kit. I did some final cleaning up of some oak legs the other day and I can’t really see how a smaller plain would do a better job.
On chisels, once a new comer learns to sharpen, Aldi sells a 4 chisel pack for about $20 US. They are blunt and the backs need to be flattened but once correctly sharpened, they hold their edge very well. These are my go to chisels for most work and they’re as sharp as a scalpel. My good chisels haven’t seen the light of day in over a year as the Aldi chisels work beautifully.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
about three years ago I thought to make even only a cutting board I would need a complete set of machines, stationary and handmachines, plus of course a few handtools for “hybrid woodworking”, then I discovered Peter Sellers and most importantly Chris and The Anarchist’s Tool Chest, that was a revelation! So I find it absolutely awesome that you show us how to start with even less tools (especially the advice for saws is great, much cheaper to only get rip)!
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
Like yourself, I get great satisfaction from working with this small kit. Similar to your wine box, I’ve got this old ‘sausage box’ that I can fit everything in, if I’m out the job site or such. It’s a lovely feeling to know that with just this small box of tools, I can pay all my bills and eat. I just wish I could get the rest of my life so minimal!
Speaking of rugged simplicity and hand tools kit – I’m very surprised to not see an axe in it! I still remember how I was amazed to see a board being split by an axe in the spoon rack premium video. Do you plan to make a blog post on this sort of topic (also because not everyone has access to premium videos)? Would be interesting to see what other coarse tools you use and when and why, and your thoughts around them. After all, the longer we stay at coarse stage the less time it will take to make something and the more efficient we are.
As someone who is just progressing past being a “beginner” (just getting into building furniture) in the woodworking community, I would say there are a number of changes I would make to your list. First, I would say that a power jointer/thicknesser does not belong on the list by any means. They are way too large of an investment and take up a lot of space (not to mention you can buy your stock at the desired dimensions). I also strongly disagree with the concept of joinery devices. As someone new to the trade, I feel this is a very important skill that must be developed, not skipped over by buying devices power devices that achieve a single goal. I think the jigsaw should be replaced by a good bandsaw. I just purchased my first major power tool and it was a 14″ bandsaw and not a tablesaw for space reasons as well as versatility. The bandsaw allows me to resaw, cut curves, (now that it is adjusted for drift) rip pieces of stock accurately that are thicker than a table saw could handle, etc. Once the cut is complete, a handplane can remove any saw marks and square/flatten a surface. It is also really useful for cutting tenons and dovetails. Handsaws can be used for crosscutting and anything else the bandsaw cannot handle. As for a bench, if you are getting into woodworking, this should be your first real project (and it is not expensive to make). You are also missing a good vise to be attached to the bench.
I agree, that’s a nice and easy set up to start with. I’d say a block plane it’s handy for small areas, and touch ups. A no.5 is excellent but a bit heavy and tiring sometimes. I find that a nice rabbet block plane (shoulder + block) with two irons with different sharpening angles it’s essential to me. One fine flat rasp and a medium flat file would complete my set.
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
While some people consider the circular saw to be more of a carpentry tool than a fine woodworking tool, but some would disagree. There may be no more versatile basic handheld power tool than a circular saw. When used with a clamp-on straight-edge, the circular saw can be just about as accurate as a table saw and handle quite a few of the tasks that one would attempt with a table saw, particularly cutting sheet goods such as plywood or medium-density fiberboard. When woodworking on a budget, a quality circular saw should be the first handheld power tool purchased, as it is the one that will likely be the most useful as you get started.
Being without machinery to dimension and dress rough timber myself I can definitely see the benefit, but I think the investment (both in money and space) in machinery like this is premature for ‘basic’ woodworking. Additionally, without some other machinery (table saw, bandsaw) you’re still going to have trouble dimensioning smaller timber for projects from large/rough stock (e.g. producing timber strips for case fronts, ripping to reduce thickness, etc).
The fourth most important basic handheld power tool every beginner should buy is a random orbital sander. While palm sanders are less expensive and can use plain sandpaper (cut into one-fourth sections), the random orbital version uses hook-and-loop fastened sanding disks, and doesn't sand in patterns, using a random sanding motion instead. This motion will serve to reduce the chance that any sanding marks may appear on the stock due to the sanding. Of course, be certain that your local woodworking supplier has sanding disks readily available in a number of grits to fit the model that you choose, as the key to proper sanding is to use progressively finer grits as you sand to reduce or remove any marks that are left behind from the previous sanding.