To start off you only need either a 1/4-inch or 3/8-inch mortise chisel (or some size close to those). I prefer 3/8-inch. You don’t need a whole set of mortise chisels. Mortise chisels (also spelled “mortice chisels”) are used for chopping mortises (rectangular holes) into the side of your board to accept the insertion of a tenon. “Mortise and Tenon” is a very common and very strong joint that most people have heard of.
But before you purchase clamps, build your first project and put it together without glue. Then see how many clamps you think you will need to put enough pressure in all the right spots. Then proceed to purchase that number of clamps. Repeat this process on your next project, and purchase more clamps if needed. This is better than running out and buying a huge collection of woodworking clamps. See my buying guide for different clamp types, uses, and my favorite brands.
When I came across your blog I was preparing to get started and looking for pointers, and decided to buy your series. In my opinion the choice to show the options was a good one. The series presented a clear overview of hand tool woodworking and you made it look easy and impressive at the same time. That series gave me the confidence to pick up the plane and start woodworking instead of coming up with a long savings plans to outfit a machine-shop. Thus, it was more an inspirational series than a build-along for me. I decided that was the kind of woodworking I wanted to be doing and began practicing. When you minimalised your kit for the later series, the builds themselves became more accessible. I felt I could actually build the pieces with the tools I had available. As a whole, you have provided me with the confidence to get started and the basic skills to continue.
After you have chosen the perfect table saw for your woodshop, the next major purchase one should consider would be a compound miter saw. While not as expensive as a quality table saw, a compound miter saw is invaluable for cutting compound angles (beveled, mitered and combination cuts) on the ends of a piece of stock. Once you develop your ability to make precise cuts with a compound miter saw, you'll find that your circular saw spends a little more time in the drawer than it used to.
A try square is used to square up your workpieces for precise-fitting joints. If you’re not confident enough to build your own try square yet, you should purchase a good metal try square (somewhere between 9 and 12 inches). It’ll be used for scribing square lines around the faces and edges of your boards, such as a line for where to cut with your saw.
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
Some might expect to see a cordless drill on this list, but when we're talking about basic power woodworking tools, a corded drill is more versatile and powerful. Sure, the cordless is, well, cordless, which makes it more portable, but corded drills are less expensive and can do more than a cordless drill. There are some options to consider when choosing a corded power drill, such as whether you want a 3/8-inch or 1/2-inch chuck, keyed or keyless chuck, straight drill or hammer drill, and so on. Learn all about these options (along with some suggestions on what to look for when shopping) in this article on corded power drills.
now I finally know what to recommend my friends when I try to convince them to give handtools a try (I currently am doing an apprenticeship in cabinetmaking (unfortunately mostly particle board) and said friends they do the same and often have no clue what can be achieved with handtools alone) because up until now, I never knew what to recommend for sharpening as my setup is great but very expensive. And I guess if I recommend to get two stones instead of a combination stone, one can keep one side flat for flattening the backs of new chisels, and add a strop with some polishing compound I really can’t think of anything else one would need for a long time!
Always be on the lookout for usable wood. You might be able to salvage some. You can use a metal detector to find nails and screws. You don’t need a full fledged metal detector. I use a pinpointer made by Garrett. If your wood has some woodboring beetles you can still use it if not eaten too badly. A healthy dose of cyfluthrin will take care of them.
I just moved overseas and had to give up all of my power tools due to space limitations and power incompatibility. Upon arrival the first power tool that I bought was a cordless drill/driver and the second was a circular saw. I then modified the saw to improve its performance for cabinet quality work by putting a zero clearance baseplate (just a piece of 1/4″ plywood screwed to the base) this allows the saw to cut plywood panels without tearing up the edges. I also bought a length of aluminum rectangle tube stock for a straight edge. Together the straight edge and the zero clearance baseplate makes the circular saw a fairly accurate tool for plywood construction projects. It’s not as easy to use as a Festool track saw but it cuts almost as clean and cost about 1/5th the price.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
A marking knife is used for marking where you will be cutting with your saws and chisels. For getting into tight spots (like dovetails) and making very accurate lines (which is vital for tight fitting joints) you need just the right marking knife. You would think that any old knife would work, but you would be wrong. Years ago I purchased several that didn’t work well.