I have to say, reading your blog and watching your videos makes me want to get started immediately on traditional woodworking. The problem I have is that hand tools are hard to come by at swap meets or antique stores out here in Bakersfield, CA. I have made several trips and so far all I have found is a beat-up old Jack plane. I would rather buy used, but I am a little leery of EBay, so my options are limited. Thank you for your posts on what to buy and links to websites. I haven’t bought anything yet, but… Read more »
No matter what woodworking or tool-related venture you're taking on, Amazon.com has the trustworthy brands delivering the helpful products you'll want, brands like Dewalt, Makita, Stanley, Black + Decker, Festool, Shop-Vac, Jet and more. You'll also find a wide range of deals and special offers on woodworking products in the Deals and Savings page. Shop on Amazon.com and get free shipping for qualifying orders.
But before you purchase clamps, build your first project and put it together without glue. Then see how many clamps you think you will need to put enough pressure in all the right spots. Then proceed to purchase that number of clamps. Repeat this process on your next project, and purchase more clamps if needed. This is better than running out and buying a huge collection of woodworking clamps. See my buying guide for different clamp types, uses, and my favorite brands.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
Now, I know this list only contains traditional hand tools, but my circumstances led me to this choice to complete the job. After all, he is my brother and he’s helped me once or twice. Not all woodworkers will want to take the time and effort to go strictly with hand tools. That’s fine; different circumstances and preferences will lead the way. Most people wouldn’t drive a scooter full of tools to assist their siblings either. Sounds crazy, but I enjoyed the trip through the mountains. Once I was there, I still needed a way to rip through lumber. I also needed a can of finish. As needed, a few jigs and templates were constructed from the purchased lumber.
Thank you for this post. I am about three years into wood working with handtools. I didn’t want to be a handtool collector. I wanted a good set of tools I could use. Since funds were tight and I wasn’t sure if I would keep doing this, I wanted to build my tools slowly. What you outlined is more or less what I ended up getting and it has indeed served me well. One can easily do a lot with all of these tools. At some point about two years into the hobby, I had a much better feel for what I wanted to make and what I may or may not need beyond this.
Wooden mallets are mostly used for hitting your chisels when cutting joints (like dovetail joints or chopping mortises). You should never hit a chisel with a metal hammer. Build or buy a mallet that is made of fairly hard wood (e.g. maple, oak, beech wood, etc.), that will feel well balanced in your hand, and that gives you enough weight to chop with your chisels.