Having very sharp tools is one of the most important aspects of proper traditional woodworking with hand tools. Many beginners think that they stink at woodworking, but usually they are just using dull (or improperly sharpened) hand tools. To start off with I recommend buying quality sharpening supplies for sharpening & honing your chisels, hand plane irons, and handsaws. And I’ll help you save money by avoiding systems that don’t work as well.
A Jack Handplane is a middle size “bench plane” (i.e. planes that are used so often that they are usually on your workbench). If you’re on a budget a jack plane can temporarily be used in place of other planes that perform specialized functions: (1) rough stock removal (if you buy a second iron/blade and shape it with a curved “camber”), (2) jointing board edges (as long as the board isn’t over 3x the length of your jack plane), and (3) smoothing the boards.
Thank you for this post. I am about three years into wood working with handtools. I didn’t want to be a handtool collector. I wanted a good set of tools I could use. Since funds were tight and I wasn’t sure if I would keep doing this, I wanted to build my tools slowly. What you outlined is more or less what I ended up getting and it has indeed served me well. One can easily do a lot with all of these tools. At some point about two years into the hobby, I had a much better feel for what I wanted to make and what I may or may not need beyond this.
Now, I know this list only contains traditional hand tools, but my circumstances led me to this choice to complete the job. After all, he is my brother and he’s helped me once or twice. Not all woodworkers will want to take the time and effort to go strictly with hand tools. That’s fine; different circumstances and preferences will lead the way. Most people wouldn’t drive a scooter full of tools to assist their siblings either. Sounds crazy, but I enjoyed the trip through the mountains. Once I was there, I still needed a way to rip through lumber. I also needed a can of finish. As needed, a few jigs and templates were constructed from the purchased lumber.
Many beginners trying to get started in woodworking take one look at their budget and worry about how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
If you are just getting into the hobby of woodworking, below is a list of woodworking tools that will help you get started. The tools we have listed are essential for having the ability to do almost any wood working project yourself. For some special projects, obviously you will need a specialized woodworking tool that may not be in our list below.
When I came across your blog I was preparing to get started and looking for pointers, and decided to buy your series. In my opinion the choice to show the options was a good one. The series presented a clear overview of hand tool woodworking and you made it look easy and impressive at the same time. That series gave me the confidence to pick up the plane and start woodworking instead of coming up with a long savings plans to outfit a machine-shop. Thus, it was more an inspirational series than a build-along for me. I decided that was the kind of woodworking I wanted to be doing and began practicing. When you minimalised your kit for the later series, the builds themselves became more accessible. I felt I could actually build the pieces with the tools I had available. As a whole, you have provided me with the confidence to get started and the basic skills to continue.
I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.