excellent post! noone can beat good advice from someone who makes a living at this. it’s struggle to commit to minimal tools but i can attest to getting too many too soon and not mastering them all. it can even slow down a project trying to fiddle with a new tool and create some waste. i’ve taken to the idea to make 6 projects with the same problem i like to solve with a specialty tool. then ask do i really need it.. for instance i want to incorporate more sliding dovetails. as per you sound advice you don’t need anything more than what you listed but i keep eyeing a dovetail planes both male and female. i just saying resist and build! learn efficiency with what i have and decide if its a roadblock to success or profitability
Speaking of rugged simplicity and hand tools kit – I’m very surprised to not see an axe in it! I still remember how I was amazed to see a board being split by an axe in the spoon rack premium video. Do you plan to make a blog post on this sort of topic (also because not everyone has access to premium videos)? Would be interesting to see what other coarse tools you use and when and why, and your thoughts around them. After all, the longer we stay at coarse stage the less time it will take to make something and the more efficient we are.
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.
Whilst I agree with everything you say there has to be a but 😀 and here it comes, after promising myself I’d have the bench of my dreams since my apprenticeship 42 years ago I finally two years ago built a three quarter ton steamed beech monster with all the bells and whistles. If only I’d had it years ago to me it’s the most important tool in my workshop now ! Solid, heavy, side and head vice, dog holes everywhere, sliding deadman the lot and yes very very pretty. But built to be used as a bench and with some visiting clients a showpiece! But more than anything because I could
Handsaws (often called “panel saws”) are long, thin saws with a comfortable wooden handle. They are used for rough dimensioning of your lumber. Although a “panel saw” is technically a smaller handsaw that fits into the panel of a tool chest, I’ll hereafter refer to this type of saw as a “Panel Saw” to differentiate them from the broad category referred to as “hand saws”. Panel saws come in two tooth configurations: “Rip” (cuts along the grain…like a chisel) and “Cross Cut” (cuts across the grain…like a knife). You will need both.
Wearing a respirator is essential when hand-applying or spraying high VOC finishes, working with mineral spirits or acetone or working with a sander or a saw. Wood dust is known to be a very dangerous workplace hazard. Long-term exposure to airborne dust can lead to all kinds of different respiratory disorders such as bronchitis, allergic rhinitis, asthma, and even cancer.
If you are just getting into the hobby of woodworking, below is a list of woodworking tools that will help you get started. The tools we have listed are essential for having the ability to do almost any wood working project yourself. For some special projects, obviously you will need a specialized woodworking tool that may not be in our list below.
Being without machinery to dimension and dress rough timber myself I can definitely see the benefit, but I think the investment (both in money and space) in machinery like this is premature for ‘basic’ woodworking. Additionally, without some other machinery (table saw, bandsaw) you’re still going to have trouble dimensioning smaller timber for projects from large/rough stock (e.g. producing timber strips for case fronts, ripping to reduce thickness, etc).
Some might expect to see a cordless drill on this list, but when we're talking about basic power woodworking tools, a corded drill is more versatile and powerful. Sure, the cordless is, well, cordless, which makes it more portable, but corded drills are less expensive and can do more than a cordless drill. There are some options to consider when choosing a corded power drill, such as whether you want a 3/8-inch or 1/2-inch chuck, keyed or keyless chuck, straight drill or hammer drill, and so on. Learn all about these options (along with some suggestions on what to look for when shopping) in this article on corded power drills.
This Combination Machine is similar to the G0634Z This Combination Machine is similar to the G0634Z except it sports our popular Polar Bear colors. It also has an end-mounted fence so you can work as close to your shop wall as possible. This feature is a real space saver and since this is a combination machine you're saving ... More + Product Details Close
Wooden mallets are mostly used for hitting your chisels when cutting joints (like dovetail joints or chopping mortises). You should never hit a chisel with a metal hammer. Build or buy a mallet that is made of fairly hard wood (e.g. maple, oak, beech wood, etc.), that will feel well balanced in your hand, and that gives you enough weight to chop with your chisels.