If I were to give someone new one piece of advice, it would be to buy their chisels new, not used. I have wasted more time and more money trying to save butchered chisels than I want to admit. There’s a good chance that the used chisel will be bellied in the back or pitted at the edge and it will take more than beginner skills to fix it. You may make things worse rather than better. Sure, learn to do this _some_ day, but maybe not as a beginner first thing. I’ve had similar problems with used planes, but it isn’t nearly as bad a problem for a joinery plane. If there are pits that lead to scratches, it may not matter for anything other than a final smoother. Also, a tiny back bevel may save the day on a plane, but you likely don’t want that on a chisel. So, I’m less fussed about planes and, if it all goes south, you can buy a new blade for smoothing work and use the old for rough work (all in the same plane). You can’t buy a new blade for a chisel. Well, you can, but it’s called buying a new chisel. I use 3/8″ a lot. 1/4, 3/8 to handle all the mortises and dovetails and either 3/4 or 1″ for paring shoulders and for fat parts of some dovetails. I probably learn towards the 1″ because there are times you want to reference off the blade to keep moving in a line, like for a housing. I think Lee Valley’s version of the Narex are excellent and mine came with flat backs that could go straight to polishing.
I recently just got into traditional woodworking and came across your YouTube channel. Your videos plus the blog posts have a depth of knowledge that cannot be found anywhere else. I have been able to buy enough tools to start a workbench and I am almost complete with the build. Your video about how to square, flatten, and dimension rough boards was a life saver! Thanks again for all your knowledge.
It is my understanding that frame saws are standard to a continental toolkit. Richard’s list of a hard-point handsaw, 10-12” backsaw, and coping saw is a very standard British/American toolkit, that preforms the same roles as the frame saws you detailed. All three are available in every hardware store in America and I assume in Britain, true hardware store back saws are now junk and to get something new that preforms as well an old Disston, like Richard stated, you have to upgrade to likes of Veritas and Lie-Nielsen.
If you can buy a bunch of tools at one time, you can save a ton on shipping, as the more you buy, the lower the rates. Also, take advantage of free shipping offers. Compare to see where you can get the best deal. Whatever you buy, make sure it is high quality. I have a Nicholson backsaw I bought at a local store before I knew of the woodworking suppliers. It has never been used much, but cuts much slower than saws such as Gramercy or Lie-Nielsen, even though mine have smaller teeth than the Nicholson.
I was telling my brother of the different ways I sharpen and he seemed interested in the slab/sandpaper method. When I went to get the extra supplies I picked up a slab of granite, adhesive, and sandpaper for sharpening. When the job was completed, the saw, the can of finish, and the slab with sandpaper were gifted to my brother. I could have shortened my list a little,
A good set of 5-7 bench chisels (they don’t have to match) will get you going right away. Down the road you’ll eventually add some specialty chisels (like paring chisels, fishtail chisels, etc) but bench chisels will work for just about everything. I often pay only $10 for high quality vintage chisels, so a compiled set can certainly be affordable, and higher quality than low quality new sets. Read the chisel buying guide to learn what chisels to avoid and which chisels will work great.
Block planes have become one of the most oft-used tools in a woodworker’s workshop. Some traditional woodworkers even keep them in their aprons! These little planes can be used to trim your joints, put chamfers on board edges, trim end grain, etc. I would recommend finding a low angle block plane, because the low angle lets you cut difficult grain more easily. My handplane buying guide goes into more detail about the features and brands that you should look for when purchasing a good quality block plane.
As someone who finds hand planing a challenge the minimalist approach seems like the best way to truly learn a tools quirks and develop the skill required. So the Veritas BU planes are going along with the Tormek required to sharpen those gargantuan irons and a diamond plate and oil stone are on the way to get my old Stanley no 5 humming. I never found a sharpening routine that didn’t look a ball ache to keep the BU planes working well and being a stick thin wimp the weight of the buggers for anything more than controlled smoothing shavings knackered me out.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.