about three years ago I thought to make even only a cutting board I would need a complete set of machines, stationary and handmachines, plus of course a few handtools for “hybrid woodworking”, then I discovered Peter Sellers and most importantly Chris and The Anarchist’s Tool Chest, that was a revelation! So I find it absolutely awesome that you show us how to start with even less tools (especially the advice for saws is great, much cheaper to only get rip)!
Just for the record, a jointer and planer are not from the ICDT kit – the philosophy on that column is, indeed, beginner AND basic (hence the Workmate). The tools we suggest in the ICDT manual are for those who are working at a kitchen table or in a backyard; the tools the editors would recommend for someone who is quite sure he or she wants to pursue serious furniture making would be rather different.
If you are just getting into the hobby of woodworking, below is a list of woodworking tools that will help you get started. The tools we have listed are essential for having the ability to do almost any wood working project yourself. For some special projects, obviously you will need a specialized woodworking tool that may not be in our list below.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
Other than the panel saw, all my kit fits into a 50x33x17cm wooden wine box. After years of relying on power tools for everything, I’ve found this minimalist approach very refreshing. Asking myself ‘will it fit in the box?’ helps me to curb ‘add to basket’ tendencies. My only additions to your list are a Stanley No. 18 block plane, a Lie Nielsen dowel plate and a small engineers set square, all non-essential but they do get used.
I consider this my “basic” tool list. Although I do not have a dedicated box for these tools, I assure you that they have a great home in cabinets, on shelves, and laying around on benches. When I do need to take my hand tools somewhere, the larger tools end up in a simple tongue and grooved latch box my grandfather owned. The smaller tools are always in my overall pockets. Overalls work great. They have multiple pockets, they’re comfortable, and they protect your upper body and legs. You only have to deal with small chunks of wood getting into the pockets, which can be dealt with if you or your other half are crafty enough to sew some flaps. It doesn’t bother me though. Thanks for your time.
A Jack Handplane is a middle size “bench plane” (i.e. planes that are used so often that they are usually on your workbench). If you’re on a budget a jack plane can temporarily be used in place of other planes that perform specialized functions: (1) rough stock removal (if you buy a second iron/blade and shape it with a curved “camber”), (2) jointing board edges (as long as the board isn’t over 3x the length of your jack plane), and (3) smoothing the boards.
Somehow I overlook #1, the jointer and thickness planer, and I saw all the other tools and immediately thought that this was my first set of tools I bought when I started working as a carpenter on a friend’s crew. Then I saw my oversight and just couldn’t get over how incongrous those two items were to the rest of the list. Had I seen a scrub plane and a jack plane I would have more harmony in the list.
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
I use chisels perhaps more than any other tool in my workshop, so it’s a good idea to not cheap out here. A high quality set of bevel edge bench chisels (new or vintage) will last you many years (likely your entire life) and will be used on nearly every project. I’ve used some descent affordable plastic handle bench chisels, but highly prefer lighter wooden handle chisels with excellent steel.
Whether you’re a seasoned woodworker or DIY pro, you’ll find the woodworking tools you need for the jobsite or around the house. Search woodworking project plans to get some fresh ideas or browse our wide tool selection to find exactly what you need. Outfit your woodworking shop with routers, sanders, table saws, dust collectors, planing tools, and hand tools from bestselling brands including Makita, Festool, Bosch, JET, Powermatic, Rockler, Grizzly, and more.
The block height’s going to be a personal thing, depending on what you use it for. Mine’s about knee height, which is on the low end, but I did use to do a tremendous amount of prepping straight from the tree. As you’re the same height as me, I’d say 33″ would be a tad on the high side. If you imagine you’ve got a longish piece of wood to work down the length, you want to be holding it almost vertical, rather than angled as it’s less likely to slip. The higher the working surface, the more angled it’s naturally going to become, hence why mine’s so low.
Wearing a respirator is essential when hand-applying or spraying high VOC finishes, working with mineral spirits or acetone or working with a sander or a saw. Wood dust is known to be a very dangerous workplace hazard. Long-term exposure to airborne dust can lead to all kinds of different respiratory disorders such as bronchitis, allergic rhinitis, asthma, and even cancer.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
Two things which I took to instantly and now wouldn’t want to do without are an old-fashioned two foot, four fold ruler which gets used all the time (there’s nothing that comes close to it) and a 1 1/2″ butt chisel which gets used all the time for marking anything which needs to be chopped e.g. the side of a mortice. It also means fewer chops and therefore a bit more accuracy when cutting out a knife wall.
My Stanley 51/2 was in a bit of a state when I got it and refurbing it took a bit of time and cash. Now it works a treat and looks like new. I’m nearly through the bench build and have spend hours using it – it really is a workhorse piece of kit. I did some final cleaning up of some oak legs the other day and I can’t really see how a smaller plain would do a better job.
I recently just got into traditional woodworking and came across your YouTube channel. Your videos plus the blog posts have a depth of knowledge that cannot be found anywhere else. I have been able to buy enough tools to start a workbench and I am almost complete with the build. Your video about how to square, flatten, and dimension rough boards was a life saver! Thanks again for all your knowledge.
Speaking of rugged simplicity and hand tools kit – I’m very surprised to not see an axe in it! I still remember how I was amazed to see a board being split by an axe in the spoon rack premium video. Do you plan to make a blog post on this sort of topic (also because not everyone has access to premium videos)? Would be interesting to see what other coarse tools you use and when and why, and your thoughts around them. After all, the longer we stay at coarse stage the less time it will take to make something and the more efficient we are.
Our Woodworking Tool index (LEFT) includes a listing of all our Woodworking Tools and materials. Throughout our site you will find exceptional values on fine woodworking tools, quality tools built to last. Woodworking Hand Tools are one of our passions and we sell the very best hand tool brands in production today. At Highland Woodworking we not only carry a great selection of top rated tools but we also provide top notch information on woodworking tools and techniques. Selecting the right woodworking tools for your woodworking shop can be overwhelming so we are always here to answer your tool questions and help you to become a better woodworker. If you are new to woodworking checkout our starter woodworking tool list for beginners. We've been offering fine woodworking tools and education since 1978, keeping woodworkers informed about the best woodworking tools, tips & techniques along the way. Purchases are backed by Highland Woodworking's 60-day money back guarantee, so you can shop us with confidence for high quality woodworking tools.
Wooden mallets are mostly used for hitting your chisels when cutting joints (like dovetail joints or chopping mortises). You should never hit a chisel with a metal hammer. Build or buy a mallet that is made of fairly hard wood (e.g. maple, oak, beech wood, etc.), that will feel well balanced in your hand, and that gives you enough weight to chop with your chisels.
WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
We offer the best hand saws for woodworking. A fine hand saw's image has long been the emblem of a craftsman at work. Used for carpentry, dovetailing, joinery and many other tasks around the shop, we stock a large variety of hand saws. You will find the hand saw you need among our selection of British Bowsaws, Gent's Saws and Tenon Saws, our extensive collection of Japanese Hand Saws, and the fine hand saws of Lie Nielsen. Be sure to check out the newest additions to our Backsaw collection from Bad Axe Tool Works - the ultimate in premium hand saws, made in the USA. Selecting the best hand saws for woodworking can be daunting, to help sort through all the options we recommend reading Essential Woodworking Hand Tools by Author Paul Sellers. His book includes a lengthy chapter on hand saws to help you decide which hand saws you need in your workshop.