Whilst I agree with everything you say there has to be a but 😀 and here it comes, after promising myself I’d have the bench of my dreams since my apprenticeship 42 years ago I finally two years ago built a three quarter ton steamed beech monster with all the bells and whistles. If only I’d had it years ago to me it’s the most important tool in my workshop now ! Solid, heavy, side and head vice, dog holes everywhere, sliding deadman the lot and yes very very pretty. But built to be used as a bench and with some visiting clients a showpiece! But more than anything because I could
If you’re on a tight budget, you can get by with just a dovetail saw for awhile. But if you have the means, then I’d recommend that you purchase three backsaws: (1) a dovetail saw, with fine rip teeth, used for cutting joinery along the grain (like dovetails), (2) a “carcass saw” used for cutting across the grain (fine cross cut teeth), and (3) a larger tenon saw used for cutting deeper cuts, like tenon cheeks, along the grain (rip teeth). All three saws are used very, very often in my workshop. As mentioned above, you could certainly get by with just a dovetail saw at first, since the small rip teeth don’t do too bad of a job at cutting across the grain. Buying backsaws can be very confusing because most sellers don’t know what saw they have, and the tooth configuration can change the job of the saw. Most people that sell antique saws mix the names up, so don’t worry. My buyer’s guide really clears this confusion up and will help you know what to look for.
I have to say, reading your blog and watching your videos makes me want to get started immediately on traditional woodworking. The problem I have is that hand tools are hard to come by at swap meets or antique stores out here in Bakersfield, CA. I have made several trips and so far all I have found is a beat-up old Jack plane. I would rather buy used, but I am a little leery of EBay, so my options are limited. Thank you for your posts on what to buy and links to websites. I haven’t bought anything yet, but… Read more »
1. Power jointer and thickness planer. I have developed various means of straightening the edges of my stock with hand-held tools, but I don’t see a way to efficiently flatten the faces of rough or reclaimed lumber without a power jointer. It’s part of the first few steps for any furniture project, and I want to be able to move through this step quickly and into the more interesting work. The thickness planer is also a huge time-saver, compared to hand-held tools.
However, I would recommend that you either build a wooden workbench, or purchase one if you feel a workbench build is too advanced for you right now. However, I created the DVD “Building the Portable Moravian Workbench with Will Myers” so that even beginners can build a solid, portable, and very affordable workbench that will fit almost anywhere, using mostly or only hand tools. You can buy it in my store here. You can find Will’s free workbench plans for the Moravian Workbench here. Whichever path you choose, make sure you choose to either build or buy a heavy & sturdy wooden workbench, with at least a 3″ solid top, strong supportive base legs, and at least one strong vise.
It is my understanding that frame saws are standard to a continental toolkit. Richard’s list of a hard-point handsaw, 10-12” backsaw, and coping saw is a very standard British/American toolkit, that preforms the same roles as the frame saws you detailed. All three are available in every hardware store in America and I assume in Britain, true hardware store back saws are now junk and to get something new that preforms as well an old Disston, like Richard stated, you have to upgrade to likes of Veritas and Lie-Nielsen.
A Jack Handplane is a middle size “bench plane” (i.e. planes that are used so often that they are usually on your workbench). If you’re on a budget a jack plane can temporarily be used in place of other planes that perform specialized functions: (1) rough stock removal (if you buy a second iron/blade and shape it with a curved “camber”), (2) jointing board edges (as long as the board isn’t over 3x the length of your jack plane), and (3) smoothing the boards.
When you go shopping for tools, get the tools for your new woodworking shop only a few at a time. As your woodworking hobby progresses, you can obtain more wood tools as time goes on. We list the woodworking tools that you will find most useful and use most often. If you are going to be doing any type of woodworking, we recommend to make a custom workbench to store your tools which will also give you with an area to perform your woodworking projects. See below for what we recommend for a basic woodworking tool kit.
I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.