Now, I know this list only contains traditional hand tools, but my circumstances led me to this choice to complete the job. After all, he is my brother and he’s helped me once or twice. Not all woodworkers will want to take the time and effort to go strictly with hand tools. That’s fine; different circumstances and preferences will lead the way. Most people wouldn’t drive a scooter full of tools to assist their siblings either. Sounds crazy, but I enjoyed the trip through the mountains. Once I was there, I still needed a way to rip through lumber. I also needed a can of finish. As needed, a few jigs and templates were constructed from the purchased lumber.
Thank you for this post. I am about three years into wood working with handtools. I didn’t want to be a handtool collector. I wanted a good set of tools I could use. Since funds were tight and I wasn’t sure if I would keep doing this, I wanted to build my tools slowly. What you outlined is more or less what I ended up getting and it has indeed served me well. One can easily do a lot with all of these tools. At some point about two years into the hobby, I had a much better feel for what I wanted to make and what I may or may not need beyond this.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
Most of your cutting will be done using power tools. While you can go full neanderthal and work solely with hand tools, modern power tools will make your woodworking hobby much more enjoyable. And you don’t really have to spend a fortune to get them. For some of them, you can easily find low budget alternatives. You can also ask your wood to be cut at the store you are buying it from.
I use chisels perhaps more than any other tool in my workshop, so it’s a good idea to not cheap out here. A high quality set of bevel edge bench chisels (new or vintage) will last you many years (likely  your entire life) and will be used on nearly every project. I’ve used some descent affordable plastic handle bench chisels, but highly prefer lighter wooden handle chisels with excellent steel.
I was telling my brother of the different ways I sharpen and he seemed interested in the slab/sandpaper method. When I went to get the extra supplies I picked up a slab of granite, adhesive, and sandpaper for sharpening. When the job was completed, the saw, the can of finish, and the slab with sandpaper were gifted to my brother. I could have shortened my list a little,

Now, I know this list only contains traditional hand tools, but my circumstances led me to this choice to complete the job. After all, he is my brother and he’s helped me once or twice. Not all woodworkers will want to take the time and effort to go strictly with hand tools. That’s fine; different circumstances and preferences will lead the way. Most people wouldn’t drive a scooter full of tools to assist their siblings either. Sounds crazy, but I enjoyed the trip through the mountains. Once I was there, I still needed a way to rip through lumber. I also needed a can of finish. As needed, a few jigs and templates were constructed from the purchased lumber.

I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.


now I finally know what to recommend my friends when I try to convince them to give handtools a try (I currently am doing an apprenticeship in cabinetmaking (unfortunately mostly particle board) and said friends they do the same and often have no clue what can be achieved with handtools alone) because up until now, I never knew what to recommend for sharpening as my setup is great but very expensive. And I guess if I recommend to get two stones instead of a combination stone, one can keep one side flat for flattening the backs of new chisels, and add a strop with some polishing compound I really can’t think of anything else one would need for a long time!
×