A good set of 5-7 bench chisels (they don’t have to match) will get you going right away. Down the road you’ll eventually add some specialty chisels (like paring chisels, fishtail chisels, etc) but bench chisels will work for just about everything. I often pay only $10 for high quality vintage chisels, so a compiled set can certainly be affordable, and higher quality than low quality new sets. Read the chisel buying guide to learn what chisels to avoid and which chisels will work great.
about three years ago I thought to make even only a cutting board I would need a complete set of machines, stationary and handmachines, plus of course a few handtools for “hybrid woodworking”, then I discovered Peter Sellers and most importantly Chris and The Anarchist’s Tool Chest, that was a revelation! So I find it absolutely awesome that you show us how to start with even less tools (especially the advice for saws is great, much cheaper to only get rip)!
Someone on here made the point that it took them a few years before they got a clear idea about what they wanted to make. I can relate to that. I’m starting to think that I’d like to do a cabinet type build so maybe a plough plane would help with that. There are plenty of old Stanley’s knocking around on Ebay. On the other hand, I’m in no hurry to buy anything else – I feel much more inclined now to make do and explore the limitations of tools that I’ve got.
I think it depends on the type of woodworker you would like to become. Are you more interested in traditional “electric free” carpentry or are you drawn to the ease and convenience of modern machinery? Also, I think you should take into consideration what kind and how much shop space you have available. I have worked with all the modern machines for years now, and are just presently finding personal satisfaction in traditional woodworking. In fact, last night I built my very first bookcase with just a few “powerless” hand tools. So in all, I would suggest some personal reflection…What type of woodworker do you want to become?…and from there garnish your shop appropriately.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
I just moved overseas and had to give up all of my power tools due to space limitations and power incompatibility. Upon arrival the first power tool that I bought was a cordless drill/driver and the second was a circular saw. I then modified the saw to improve its performance for cabinet quality work by putting a zero clearance baseplate (just a piece of 1/4″ plywood screwed to the base) this allows the saw to cut plywood panels without tearing up the edges. I also bought a length of aluminum rectangle tube stock for a straight edge. Together the straight edge and the zero clearance baseplate makes the circular saw a fairly accurate tool for plywood construction projects. It’s not as easy to use as a Festool track saw but it cuts almost as clean and cost about 1/5th the price.
The third tool for the beginner is the Jigsaw. A jigsaw allows the user to cut curved and circular patterns in stock. Sure, a band saw will likely be more accurate and can cut thicker stock, but for the beginner, the jigsaw (sometimes also referred to as a Sabre Saw) can be perfectly effective. For versatility, choose an orbital-action, corded jigsaw that feels good in your hand and has an easy blade changing system.
I just found you site and from what I have seen so far is very impressive. I cannot believe it took me this long to find it. I have a question concerning the Stanley 62 folding rule that you and Chris Schwarz recommend. I checked on ebay and there seems to be a wide range in prices. Do you have any more information or a recommendation as to the where more research could be done on these rules? Also, if I win the video, I would like the Howarth Bow Saw video and/or the black Got Wood? t-shirt. I live… Read more »