I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
To start off you only need either a 1/4-inch or 3/8-inch mortise chisel (or some size close to those). I prefer 3/8-inch. You don’t need a whole set of mortise chisels. Mortise chisels (also spelled “mortice chisels”) are used for chopping mortises (rectangular holes) into the side of your board to accept the insertion of a tenon. “Mortise and Tenon” is a very common and very strong joint that most people have heard of.
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.
Many beginners trying to get started in woodworking take one look at their budget and worry about how they can afford to buy a whole shop full of power tools to get started. Fortunately, one doesn't have to spend a fortune to get started. There are really only seven woodworking tools that I would recommend any beginning woodworker have on hand from the start, and most are relatively inexpensive. However, with these seven tools, a beginner can tackle quite a number of projects.

1. Power jointer and thickness planer. I have developed various means of straightening the edges of my stock with hand-held tools, but I don’t see a way to efficiently flatten the faces of rough or reclaimed lumber without a power jointer. It’s part of the first few steps for any furniture project, and I want to be able to move through this step quickly and into the more interesting work. The thickness planer is also a huge time-saver, compared to hand-held tools.
Whilst I agree with everything you say there has to be a but 😀 and here it comes, after promising myself I’d have the bench of my dreams since my apprenticeship 42 years ago I finally two years ago built a three quarter ton steamed beech monster with all the bells and whistles. If only I’d had it years ago to me it’s the most important tool in my workshop now ! Solid, heavy, side and head vice, dog holes everywhere, sliding deadman the lot and yes very very pretty. But built to be used as a bench and with some visiting clients a showpiece! But more than anything because I could
I recently just got into traditional woodworking and came across your YouTube channel. Your videos plus the blog posts have a depth of knowledge that cannot be found anywhere else. I have been able to buy enough tools to start a workbench and I am almost complete with the build. Your video about how to square, flatten, and dimension rough boards was a life saver! Thanks again for all your knowledge.
Someone on here made the point that it took them a few years before they got a clear idea about what they wanted to make. I can relate to that. I’m starting to think that I’d like to do a cabinet type build so maybe a plough plane would help with that. There are plenty of old Stanley’s knocking around on Ebay. On the other hand, I’m in no hurry to buy anything else – I feel much more inclined now to make do and explore the limitations of tools that I’ve got.
We offer the best hand saws for woodworking. A fine hand saw's image has long been the emblem of a craftsman at work. Used for carpentry, dovetailing, joinery and many other tasks around the shop, we stock a large variety of hand saws. You will find the hand saw you need among our selection of British Bowsaws, Gent's Saws and Tenon Saws, our extensive collection of Japanese Hand Saws, and the fine hand saws of Lie Nielsen. Be sure to check out the newest additions to our Backsaw collection from Bad Axe Tool Works - the ultimate in premium hand saws, made in the USA. Selecting the best hand saws for woodworking can be daunting, to help sort through all the options we recommend reading Essential Woodworking Hand Tools by Author Paul Sellers. His book includes a lengthy chapter on hand saws to help you decide which hand saws you need in your workshop.
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
Most of your cutting will be done using power tools. While you can go full neanderthal and work solely with hand tools, modern power tools will make your woodworking hobby much more enjoyable. And you don’t really have to spend a fortune to get them. For some of them, you can easily find low budget alternatives. You can also ask your wood to be cut at the store you are buying it from.
“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!
Once you have the four aforementioned handheld power tools in your arsenal and you've had time to get comfortable with using them, its time to make your first (and likely most important) major tool purchase. The table saw is the heart and soul of every woodworking shop, the centerpiece around which all of the other tools are used and organized, so you'll want to buy the best table saw that your budget can comfortably afford. Take the time to learn which features you really want and the table saw that best fits your budget and your needs. This article will show you the most common features, and how to determine what features you need and how to know if those features are really well built, or simply added on to the saw because they are selling features.
I consider this my “basic” tool list. Although I do not have a dedicated box for these tools, I assure you that they have a great home in cabinets, on shelves, and laying around on benches. When I do need to take my hand tools somewhere, the larger tools end up in a simple tongue and grooved latch box my grandfather owned. The smaller tools are always in my overall pockets. Overalls work great. They have multiple pockets, they’re comfortable, and they protect your upper body and legs. You only have to deal with small chunks of wood getting into the pockets, which can be dealt with if you or your other half are crafty enough to sew some flaps. It doesn’t bother me though. Thanks for your time.
excellent post! noone can beat good advice from someone who makes a living at this. it’s struggle to commit to minimal tools but i can attest to getting too many too soon and not mastering them all. it can even slow down a project trying to fiddle with a new tool and create some waste. i’ve taken to the idea to make 6 projects with the same problem i like to solve with a specialty tool. then ask do i really need it.. for instance i want to incorporate more sliding dovetails. as per you sound advice you don’t need anything more than what you listed but i keep eyeing a dovetail planes both male and female. i just saying resist and build! learn efficiency with what i have and decide if its a roadblock to success or profitability

If you can buy a bunch of tools at one time, you can save a ton on shipping, as the more you buy, the lower the rates. Also, take advantage of free shipping offers. Compare to see where you can get the best deal. Whatever you buy, make sure it is high quality. I have a Nicholson backsaw I bought at a local store before I knew of the woodworking suppliers. It has never been used much, but cuts much slower than saws such as Gramercy or Lie-Nielsen, even though mine have smaller teeth than the Nicholson.
For a huge and amazingly useful website with hundreds of quick tips and tricks for woodworking, visit woodworking tips to find some of the most useful things that will assist you with all things woodworking. If you have a question or need a tip on getting something done concerning your woodworking project, the woodworking tips website will be a great resource.
×